| General information |
| Product type designation |
F-DQ 8x24VDC/2A PPM |
| Firmware version |
|
| ● FW update possible |
Yes |
| Product function |
| ● I&M data |
Yes; I&M0 to I&M3 |
| Engineering with |
| ● STEP 7 TIA Portal configurable/integrated as of version |
V13 SP1 with HSP 0086 |
| Operating mode |
| ● DQ |
Yes |
| Supply voltage |
| Type of supply voltage |
24 V DC |
| Rated value (DC) |
24 V |
| permissible range, lower limit (DC) |
19.2 V |
| permissible range, upper limit (DC) |
28.8 V |
| Reverse polarity protection |
Yes |
| Input current |
| Current consumption (rated value) |
110 mA; without load |
| Output voltage |
| Rated value (DC) |
24 V |
| Power |
| Power available from the backplane bus |
0.8 W |
| Power loss |
| Power loss, typ. |
11 W |
| Address area |
| Address space per module |
| ● Address space per module, max. |
6 byte |
| Hardware configuration |
| Automatic encoding |
Yes |
| ● Electronic coding element type F |
Yes |
| Digital outputs |
| Number of digital outputs |
8 |
| Current-sinking |
Yes |
| Current-sourcing |
Yes |
| Short-circuit protection |
Yes |
| Open-circuit detection |
Yes |
| ● Response threshold, typ. |
8 mA |
| Overload protection |
Yes |
| ● Response threshold, typ. |
2.9 A |
| Limitation of inductive shutdown voltage to |
PM-switching: -24 V + (-47 V), PP-switching: -24 V |
| Switching capacity of the outputs |
| ● with resistive load, max. |
2 A |
| ● on lamp load, max. |
10 W |
| Load resistance range |
| ● lower limit |
12 Ω |
| ● upper limit |
2 000 Ω |
| Output voltage |
| ● for signal "1", min. |
24 V; L+ (-0.5 V) |
| Output current |
| ● for signal "1" rated value |
2 A |
| ● for signal "0" residual current, max. |
0.5 mA; Current-sourcing, or current sourcing and sinking switches individually, current sinking: max. 1 mA |
| Switching frequency |
| ● with resistive load, max. |
30 Hz |
| ● with inductive load, max. |
0.1 Hz |
| ● on lamp load, max. |
10 Hz |
| Total current of the outputs |
| ● Current per channel, max. |
2 A |
| Total current of the outputs (per module) |
| horizontal installation |
| — up to 40 °C, max. |
16 A |
| — up to 60 °C, max. |
8 A |
| vertical installation |
| — up to 40 °C, max. |
8 A |
| Cable length |
| ● shielded, max. |
1 000 m |
| ● unshielded, max. |
500 m |
| Interrupts/diagnostics/status information |
| Diagnostics function |
Yes |
| Substitute values connectable |
No |
| Alarms |
| ● Diagnostic alarm |
Yes |
| Diagnostic messages |
| ● Monitoring the supply voltage |
Yes |
| ● Wire-break |
Yes |
| ● Short-circuit |
Yes |
| ● Group error |
Yes |
| Diagnostics indication LED |
| ● RUN LED |
Yes; Green LED |
| ● ERROR LED |
Yes; Red LED |
| ● Monitoring of the supply voltage (PWR-LED) |
Yes |
| ● Channel status display |
Yes; Green LED |
| ● for channel diagnostics |
Yes; Red LED |
| ● for module diagnostics |
Yes; Red LED |
| Potential separation |
| Potential separation channels |
| ● between the channels |
No |
| ● between the channels and backplane bus |
Yes |
| Isolation |
| Isolation tested with |
707 V DC (type test) |
| Standards, approvals, certificates |
| Highest safety class achievable in safety mode |
| ● Performance level according to ISO 13849-1 |
PLe |
| ● SIL acc. to IEC 61508 |
SIL 3 |
| Probability of failure (for service life of 20 years and repair time of 100 hours) |
| — Low demand mode: PFDavg in accordance with SIL3 |
< 6.00E-05 |
| — High demand/continuous mode: PFH in accordance with SIL3 |
< 2.00E-09 1/h |
| Ambient conditions |
| Ambient temperature during operation |
| ● horizontal installation, min. |
0 °C |
| ● horizontal installation, max. |
60 °C |
| ● vertical installation, min. |
0 °C |
| ● vertical installation, max. |
40 °C |
| Dimensions |
| Width |
35 mm |
| Height |
147 mm |
| Depth |
129 mm |
| Weights |
| Weight, approx. |
300 g |
| last modified: |
11/10/2018 |
