AC Drive PowerFlex400, 15kW 30A 3x480VAC, integral keypad?LED display, RS485, frame C, Rockwell Automation

PowerFlex®400 Air Cooled Drive, Voltage Rating: Input: 308 - 480 V, Output: 480 VAC, Amperage Rating: 30 A, Wattage: 15 KW, Phase: 3 PH, HP Rating: 20 HP, Frame Size: Size C, Frequency Rating: 50/60 HZ, Power Factor: 0.98, Control: RS-485, Mounting: Panel, Display: Integral Keypad And LED, Connection: Fixed Terminal, Enclosure: IP20, Open Type, Environmental Conditions: Altitude: 1000 M (3300 FT) max. without derating. Above 1000 M (3300 FT) derate 3% for every 305 M (1000 FT), Air Temperature: -10 To 50 DEG C, Storage Temperature: -40 To 85 DEG C, Relative Humidity: 0 - 95%, Shock (Operating): 15G Peak For 11 MS Duration, Vibration (Operating): 1G Peak, 5 - 2000 HZ, Dimension: 10.2 IN Height X 5.1 IN Width X 7.1 IN Depth

• Item Name: Air Cooled Drive

• Sub Brand: PowerFlex®400

• Voltage Rating: Input: 308 - 480 V, Output: 480 VAC

• Amperage Rating: 30 A

• Wattage: 15 KW

• Phase: 3 PH

• HP Rating: 20 HP

• Frame Size: Size C

• Frequency Rating: 50/60 HZ

• Power Factor: 0.98

• Control: RS-485

• Mounting: Panel

• Display: Integral Keypad And LED

• Connection: Fixed Terminal

• Enclosure: IP20, Open Type

• Environmental Conditions: Altitude: 1000 M (3300 FT) max. without derating. Above 1000 M (3300 FT) derate 3% for every 305 M (1000 FT), Air Temperature: -10 To 50 DEG C, Storage Temperature: -40 To 85 DEG C, Relative Humidity: 0 - 95%, Shock (Operating): 15G Peak For 11 MS Duration, Vibration (Operating): 1G Peak, 5 - 2000 HZ

• Dimension: 10.2 IN Height X 5.1 IN Width X 7.1 IN Depth

• Built in auxiliary motor control
• Operation of up to three (3) line-started motors in addition to the motor controlled directly by the PowerFlex 400 drive
• When auxiliary motor control is enabled, the internal PID controller in the PowerFlex 400 uses a reference and feedback signal to adjust the speed of the drive controlled motor such that the feedback signal follows the reference signal
• The speed of the drive controlled motor is reduced to account for the auxiliary motors additional output to the system
• A motor interlock input identifies motors that are out of service and causes them to skipped over to the next available motor
• AutoSwap function also can be used which allows equal wear to be placed on each motor by periodically swapping the drive controlled and auxiliary motors
• Each motor in the system will over time be connected to the PowerFlex 400 drive and also directly to the AC line
• During an autoswap, the motor directly connected to the PowerFlex 400 drive is stopped and the contactor is opened
• The contactor of the next motor that will be controlled by the PowerFlex 400 drive is opened if running across the AC line
• Without filtered emission class
• Drive has an input which can be wired to a fire control panel or other fire/life safety systems allowing control of the drive to be overridden
• A purge input will start the drive at a programmable purge speed regardless of the selected start source, purge can occur and is operational at any time whether the drive is running or stopped
• A purge command will take precedence over a stop command from the comm port/network and over a “SW Enable” command from the terminal block
• Standards: Listed to UL508C and CAN/CSA-22.2, listed to UL508C for plenums, certified to AS/NZS, 1997 group 1, class A, EMC directive (89/336) EN 61800-3, EN 50081-1, EN 50082-2, EN 50178, EN 60204